Welcome to Acoustic Frontiers Blog

Creating a system you love shouldn't be difficult. The Acoustic Frontiers blog is here to help.

Using subwoofers to improve sound quality: Part 2 - Room Modes

by Nyal Mellor October 26, 2010

An introduction to modal resonances

Room modes are caused by perfect constructive interference between a sound wave traveling between two boundaries. In rectangular rooms the first axial mode of a room can be found through an application of the wavelength formula as follows:

1st modal frequency = speed of sound / 2 * distance between boundaries

The axial modes contain the most power and therefore typically cause the largest problems. These modes are caused by interference between two parallel surfaces i.e. those related to the length, width and height dimensions of the room. Let's look at an example to help illustrate things: The 1st axial mode for a 20ft long room would be: 1140ft per second / (2 x 20ft) = 28.5Hz. If we examined this room using a high resolution acoustic measurement we would expect to see a peak in the frequency response and ringing in the time domain at the resonance frequency (i.e. 28.5Hz). From a sound quality perspective we would expect to hear lack of smoothness, boomy bass and also an impact on clarity, as low level sounds are obscured by the excessive length of time it takes for bass notes to decay.

There are also tangential and oblique modes, which are less powerful and are formed by interference between four and six boundaries respectively. The final consideration is to realize that more than one pattern of constructive interference can fit between two boundaries. In fact modal resonances can be found at multiples of the 1st modal frequency i.e. 28.5*2 (57ft), 28.5*3 (85.5ft), 28.5*4 (114ft), etc. We won't discuss these added complications further but it is important to be aware of them.

How to use subwoofer placement and numbers to reduce the impact of room modes

To simplify things we will just consider one example - using subwoofers reduce the impact of the 1st axial length mode. The diagram below shows what we would expect to see if we were to measure how sound pressure level varies by distance between the front and back walls of our 20ft long room.

 /></span></span></p>
<p>Looking at the diagram you can see that SPL is a maximum near the walls and at a minimum in the center of the room. The minimum point is called a 'null'. Each side of the null the lobes of the room mode are in opposite polarity.</p>
<p>The effect of a subwoofer on the level of a room mode depends upon where you put the subwoofer. If you put it in the center of the room at the null there would be no energy coupling between the subwoofer and the mode. The mode would not be excited and there would be no measureable peak in the frequency response or ringing in the time domain.</p>
<p>The other way to achieve the same effect is to use two subwoofers, each of which is positioned in a lobe of different acoustic polarity. This means that the positive sound wave created by the subwoofer in the left, positive lobe is met by a sound wave of equal level but negative polarity created by the subwoofer in the other lobe. If you have two sound waves that are identical in frequency and level but the polarities are opposite then there will be perfect cancellation. This means that there will again not be any measurable frequency response peak or time domain ringing.</p>
<p>There is so much that can be achieved by listening to a system to identify a sound quality issue, using measurements to find the cause and then using appropriate solutions. In this case I hope you can see how subwoofers can be used to effectively solve some room mode related problems.</p>
<p> </p></div>




Nyal Mellor
Nyal Mellor

Author



Also in Low Frequency Optimization

JL Audio show the E112 - a new lower cost 12" subwoofer - at CES

by Nyal Mellor January 22, 2012 0 Comments

JL Audio, the manufacturer of the superb Fathom F110, F112, F113, F212 and Gotham subwoofers showed their new E112 subwoofer at CES. I have seen this sub before, at CI Expo, a custom integrator event that was held in Berkeley this year. But this is the first time I had my camera with me to take some photos!

JL Audio E112 subwoofer

Continue Reading

Subwoofer setup and integration 101: sub crossover frequency, slope and phase for two channel systems

by Nyal Mellor October 11, 2011 0 Comments

Continue Reading

Two channel amplifiers with bass management and room correction!

by Nyal Mellor May 13, 2011 0 Comments

Recently I have become aware of a new class of product: two channel amplifiers WITH bass management AND room correction. Why is this cool? Well until this new class of products came out the only way to do this type of thing was with a home theater receiver or a separate preamplifier such as a DEQX or TacT and a power amplifier. Two channel systems benefit just as much from subwoofers and equalization as home theater systems. Many two channel speakers, even high end ones, cannot reproduce low bass below say 30-40Hz with low distortion. A JL Audio F112 can play down to 19Hz at a -3dB point! Using subwoofers also allows for cunning room mode cancellation and avoidance of speaker boundary interference.

Classe CP-800

Continue Reading

Contact Us About This Product

video-design

Nyal Mellor, Founder, Acoustic Frontiers

  • (415) 524-8741
  • Serving USA & Canada
  • Fairfax, Northern California, USA

ask us a question about this product